The cleaning procedure for a whirlpool bath is a bit different from a basic tub and shower cleaning routine. Turn it off once the jets are covered by 23 inches of water.

3 Smart Simple Ways To Clean A Jetted Tub Clean Jetted Tub Jetted Tub Window Cleaning Tips

Then add 2 tablespoons of liquid dishwashing detergent to the water followed by 12 cup of vinegar or bleach to disinfect the tub.

How to clean bathtub jets. Run the jets for approximately 15 minutes to effectively clear any debris that may be clogged inside. If you havent used your jetted whirlpool tub in some time you could be in for a surprise when you turn them on and find dust old soap scum even bugs blas. This can help remove grime and get excess cleaner out of the jets.

Pay special attention to the waterline area the faucet and the area around the drain. Add 12 cup of laundry detergent or the amount used to clean 1 load of laundry as recommended by the detergent manufacturer. Sprinkle a coating of baking soda over your tub then scrub with an old damp cloth.

If you need a really deep clean you can attack the jets with a bottle brush and a nonabrasive cloth. Place about one cup of baking soda in a small bowl or measuring cup. Fill the tub with hot water approximately an inch above the highest jet.

Clean the jetted tub after every 1 to 3 months if the user uses the tub daily or several times a week. There may be times when running a cleaning solution through the tubes is not enough. For the first step fill the tub with hot water up to two to three inches above the highest jets.

Empty the tub and refill it cold water is fine this time. Fill the tub with hot water to at least three inches above the height of the jets. Drain the tub and rinse it well to get the gunk off.

Then drain the water. They need to turn the hot water on and wait until it fills the tub. Add two to four teaspoons of powdered dishwasher detergent or another low-foaming disinfectant.

Just a short video on how to remove jets from your tub. If theres still dirt around the jet covers try using dental floss to get behind them. Scrub gently with baking soda.

Use the brush to clean the interior surfaces of each jet. Use a bottle brush and a soft cloth to clean into the jet mechanism. How to Clean a Bathtub - How to Clean a Bathtub with JetsWhen was the last time you cleaned your jetted tub.

Run the jets for 10 minutes more. Run the tubs jets for 15 minutes. Flush accumulated gunk and bacteria from internal tub plumbing.

Flush the tub one more time. Clean the Jets. Make sure the water temperature reaches at least 140º F 60º C.

My favorite thing to use for cleaning bathtubs is baking soda. This does not include the casual wipe down whil. Run the jets for 15 minutes.

Dip an old toothbrush or small bottle brush in the dry baking soda. These jets create the unique whirlpool spa experience but the jets also draw in and push out the water used in the bath. First of all the user needs to fill out the tub using the hot water.

Here are three ways to clean bathtub jets with your hands. Use a soft clean rag to wipe around the jets after your cleaning. The Jacuzzi bath has bathtub jets within the unit out of plain sight.

Turn off the air-induction valves. Its abrasive enough to take away mold and soap scum but it doesnt scratch the tub. Run the jets for 15 minutes and then turn off and drain the bathtub.

To clean a jetted tub start by filling it with hot water so all of the jets are covered. For cleaning a jetted tub with vinegar fill the hot tub with water covering the jets with approximately two inches of hot waterPour the vinegar into the hot tub and run the jets for 15 minutes to allow the vinegar to cycle through the tub and the jets. Wait half an hour before turning the tub jets back on for an additional 15 minutes.

I could never truly clean behind the jets on my jetted tub. How to Clean a Jetted Tub. When I bought my house I was never give.

For a deep clean you can also add up to one-half cup of bleach. Add dishwashing detergent either powder or liquid soap then mix in one cup of vinegar. Turn on the jets and let them run for 15 minutes.

Fill the Jacuzzi tub with cold water until its above the highest jets. A nice shot of cold water through the system will get rid of any remaining debris and will leave your whirlpool tub clean and sterile.